Tất cả bài viết

The Mexican government has announced anti-dumping duties on cold-rolled coils imported from Vietnam, with the anti-dumping duties ranging from 11.6% to 79%. These duties have been adjusted to lower levels compared to the initial rates proposed by the Mexican Ministry of Economy in September.Alongside robust growth in export activities, Vietnam's steel products are currently among the most frequently subjected to anti-dumping and countervailing investigations initiated by countries worldwide. Many steel products have faced lawsuits and have been subject to anti-dumping and countervailing duties in major markets such as the United States, the European Union, India, Australia, and more. Most recently, the Mexican government has decided to impose anti-dumping duties on cold-rolled coil products imported from Vietnam.It is known that Vietnam and Mexico are both members of the Comprehensive and Progressive Agreement for Trans-Pacific Partnership (CPTPP), so Vietnam's cold-rolled coil products enjoy a preferential tariff rate of 0% when exported to Mexico. For the groups of cold-rolled coil products currently under anti-dumping investigation, the total export turnover in 2020 was approximately 50 million USD. Among them, the HS code 7209 for cold-rolled iron and steel products accounted for nearly 80% of the production. This marked the second instance of Mexico initiating a trade remedy investigation against Vietnam, following an earlier anti-dumping investigation on coated steel products in 2021.On July 28, 2022, the Mexican Ministry of Economy initiated an anti-dumping investigation into cold-rolled coils imported from Vietnam based on complaints from the domestic industry. This action was taken in response to the observed unfair international trade practices affecting the country's enterprises. Under the guise of price discrimination, the cold-rolled coil products from Vietnam were deemed to have caused economic harm, leading to a decline in revenue for domestic steel manufacturers.After a period of investigation, the Mexican government has recently implemented anti-dumping duties on cold-rolled coil products imported from Vietnam. Starting from December 29, imported cold-rolled coil products from Vietnam had been subjected to anti-dumping duties imposed by the Mexican government. Specifically, the rates are 11.64% for products imported from Hoa Phat, 25.64% for those from Posco Vietnam and 79.24% for other manufacturers. In comparison, preliminary duties announced in September were 12.77% for Hoa Phat, 25.64% for Posco Vietnam and 81.06% for other manufacturers.The anti-dumping duties are applicable to items with the following HS codes: 7209.16.01, 7209.17.01, 7209.18.01, 7209.26.01, 7209.27.01, 7209.28.01, 7209.90.99, 7211.23.03, 7211.29.99, 7211.90.99, 7225.50.91, and 7226.92.06. Currently, steel products imported into Mexico also require a special import license issued by the Mexican government. In the context where the capabilities to respond to anti-dumping investigations by exporting businesses still have many shortcomings, fostering sustainable growth and exports and avoiding protectionist trade measures requires enterprises to adapt appropriately to the new circumstances. Faced with these challenges, Vietnamese businesses need to diversify risks, explore new export markets and enhance the value-added content of the domestic production chain. By doing so, the manufacturing sector can develop sustainably, minimizing the risk of investigations and applying anti-avoidance measures imposed by importing countries. Additionally, businesses should improve their traceability systems and accounting records to support anti-dumping investigations and facilitate the registration of self-certification mechanisms for the origin of raw materials in products subject to anti-avoidance investigations.

Malaysia has imposed definitive anti-dumping duties on Japanese cold-rolled steel coils after the Ministry of Investment, Trade and Industry (MITI) concluded its investigation earlier this year. At the same time, Malaysia also announced the end of trade defense measures on cold rolled steel imported from Vietnam.1. Malaysia: Anti-dumping investigation on Japanese cold rolled steelAccording to MITI's report, Malaysia's steel plate demand in 2022 reached 3.5 million tons, down 5.4% compared to the previous year. In the same year, import and export of steel plates both decreased by about 6-7% compared to 2021. Meanwhile, Malaysian cold-rolled steel prices remained highly competitive due to the massive import of cheap steel from abroad.This posed a significant threat to the development and business operations of domestic factories. Therefore, the Malaysian government is forced to take trade defense measures to protect the domestic market to a certain extent.On January 31, 2023, the authorities conducted an AD investigation on cold-rolled coils of iron or non-alloy steel with a width above 1300mm from Japan. The affected products are classified under the following HS code groups: 7209.15.00 00, 7209.16.10 00, 7209.16.90 00, 7209.17.10 00, 7209.17.90 00, 7209.18.99 00, 7209.25.00 00, 720 9.26. 10 00, 7209.26.90 00, 7209.27.10 00, 7209.27.90 00, 7209.28.90 00, 7209.90.90 00, 7211.23.20 00, 7211.23.90 00, 7211.29.2 0 00, 7211.29.90 00, 7211.90. 11 00, 7211.90.12 00, 7225.50.90 00, 7225.99.90 00, 7226.92.10 00 and 7226.92.90 00.2. Malaysia: Applying anti-dumping duty on Japanese cold rolling millsOn September 29, 2023, Malaysia imposed anti-dumping duties on Japanese cold-rolled coils of iron or non-alloy steel with thickness of 0.2-2.6mm and width of 700-1300m after completing the investigation. Accordingly, the Malaysian government has imposed a duty rate of 9.03% on Nippon Steel Corporation and 22.62% on other manufacturers, effective until September 28, 2028. However, due to the benefits of black plate and cold-rolled steel coils for the automobile, electronics industries are so great, Malaysia has excluded AD for these products.3. Malaysia: Ending anti-dumping measures on Vietnam's cold-rolled steelAccording to the Trade Defense Department, on March 21, 2019, MITI initiated an investigation of cold-rolled coils of iron or non-alloy steel with a width above 1300mm imported from Japan, Korea, China and Vietnam.By December 17, 2019, the government had applied definitive anti-dumping duty rates as follows: China 4.76% - 26.38% of the CIF value, Japan 26.39% of the CIF value, Korea 7.7% or 20.13% of the CIF value. This rate is effective for 5 years, from December 25, 2019 to December 24, 2024.In addition, other products from Vietnam and Korea are also under investigation including alloy/non-alloy cold rolled steel coils with thicknesses 0.2 - 2.6mm and widths 700 - 1300mm. The case has undergone many sunset reviews and received a decision to continue imposing anti-dumping duty, effective until October 8, 2026 at a rate of 0 - 21.64% for Korea and 7.42 - 33.7% for Vietnam. However, under the petition efforts of the Vietnamese government, MITI founded that Vietnam did not violate export conditions, the dumping margin was less than 2% of the export price. Therefore, Malaysia ended anti-dumping measures on the above products. In conclusion, Malaysian importers continue to enjoy preferential duty rates and cheap, quality steel sources from Vietnam.Vietnam is proud to be one of Malaysia's largest steel exporters with 653.7 million USD of iron and steel of all kinds and 48.1 million USD of steel products in 2022. Additionally, Vietnam and Malaysia are both members of the Association of Southeast Asian Nations (ASEAN) and ASEAN Free Trade Area (AFTA). There are many favorable opportunities for increased trade and two-way economic cooperation. If customers have any questions about the latest policies and procedures for importing Vietnamese steel, please contact MRS Steel via Email vanloc@mrssteel.com.vn for the most thoughtful support.

The cold-rolled coil product is appreciated for its diverse applications and outstanding advantages. So how is cold rolled steel manufactured and what are its current popular applications, all questions will be answered in the article below!What is the cold rolled coil?Cold-rolled steel (trademarked CRC) is generated at the final stage of making steel from billet. Cold rolled coils are produced based on steel billets at low temperatures, more specifically, CRC has origin from hot rolled steel, then it will be processed through a cool process to make the surface become smooth and improve eye-catching brightness.Features of cold rolled coils Cold rolled coil often possesses a glossy surface by an oil layer treated in the rolling process. Besides the smooth surface, the product also offers outstanding durability advantages 20% higher than hot rolled coil. Along with that, cold rolled coil also has good impact resistance and ductile properties, so it is easy to bend and cut on requests.However, because it is still a metal, the cold rolled coil is easy to oxidize if it is not well preserved. Specifically, when the product exists in highly acidic or alkaline environments as well as it has to suffer from harsh weather environments, it will easily cause the steel surface to rust. To overcome this situation, the manufacturer usually has to periodically maintain it by applying a layer of oil to create a protective film for the steel core.Process production of cold rolled coilsThe steel production process will have to go through many separate stages that require strict control to ensure the hardness of the steel and avoid the case that the compositional elements are changed during the period of production.Stage 1 - Preparation of input materials and removing rust surface: the main input material of cold rolled coil is hot rolled coil. Hot rolled coil often brings low aesthetics through the rough appearance, so the manufacturer will proceed to spray a specialized acid directly on the surface to clean it.Stage 2 - Cold rolling stage: the manufacturer will use mechanical force with oil to roll the steel at a low temperature which is equal to room temperature at that time. This cold rolling process has the effect of making the steel structure stronger as well as changing the surface of the steel. However, in principle, the cold rolling process only changes the steel structure and it will keep the original steel's compositions. Because of those technical standards, cold rolling stages will require strict control in order to avoid surface cracking due to excessive force.Stage 3 - Soft annealing: steels that have undergone the cold rolling process will often be in hard condition, so they will be treated with a next step, which is soft annealing. The steel will now be annealed in an electric furnace containing 100% hydrogen gas to help remove the hardness after rolling, enhancing the ductility of the steel to make use of construction applications.Application in specific fieldsDepending on outstanding advantages such as shiny appearance, good loading resistance, cold rolled coil is widely used in the construction, manufacturing and mechanical industries. It also shows some benefits to human daily life. Specifically, some popular areas include:Construction works: taking advantage of the sturdy structure thanks to the low carbon content, people often use CRC for many construction purposes. Some practical applications in popular construction include making structural frames, purlins, ...Machine parts, spare parts for automobile and aircraft equipmentHousehold and consumer appliances: refrigerators, air conditioners, stoves,... Looking for cold rolled coil suppliers directly from Vietnamese factoriesSince the company was established and entered the market until now, MRS Steel has always maintained our mission of being a pioneer in the field of providing comprehensive steel solutions for international importers. Recognizing the important role of cold rolled steel, MRS Steel has been present and accompanies you in finding reputable sources.Based on many years of experience in the steel industry, we are confident in accompanying you in the steel import strategy. Vietnam steel market is considered a potential market with the participation of countless large and small manufacturers, acquiring a consultant  in steel will help you significantly optimize time and cost in the future. By finding out the source of goods as well as knowing the detailed price list, you can promptly adjust and orient your trading planning based on useful data.